Next: , Previous: mmo, Up: mmo



3.5.1 File layout

The mmo file contents is not partitioned into named sections as with e.g. ELF. Memory areas is formed by specifying the location of the data that follows. Only the memory area 0x0000...00 to 0x01ff...ff is executable, so it is used for code (and constants) and the area 0x2000...00 to 0x20ff...ff is used for writable data. See mmo section mapping.

There is provision for specifying “special data” of 65536 different types. We use type 80 (decimal), arbitrarily chosen the same as the ELF e_machine number for MMIX, filling it with section information normally found in ELF objects. See mmo section mapping.

Contents is entered as 32-bit words, xor:ed over previous contents, always zero-initialized. A word that starts with the byte 0x98 forms a command called a lopcode, where the next byte distinguished between the thirteen lopcodes. The two remaining bytes, called the Y and Z fields, or the YZ field (a 16-bit big-endian number), are used for various purposes different for each lopcode. As documented in http://www-cs-faculty.stanford.edu/~knuth/mmixal-intro.ps.gz, the lopcodes are:

lop_quote
0x98000001. The next word is contents, regardless of whether it starts with 0x98 or not.
lop_loc
0x9801YYZZ, where Z is 1 or 2. This is a location directive, setting the location for the next data to the next 32-bit word (for Z = 1) or 64-bit word (for Z = 2), plus Y * 2^56. Normally Y is 0 for the text segment and 2 for the data segment.
lop_skip
0x9802YYZZ. Increase the current location by YZ bytes.
lop_fixo
0x9803YYZZ, where Z is 1 or 2. Store the current location as 64 bits into the location pointed to by the next 32-bit (Z = 1) or 64-bit (Z = 2) word, plus Y * 2^56.
lop_fixr
0x9804YYZZ. YZ is stored into the current location plus 2 - 4 * YZ.
lop_fixrx
0x980500ZZ. Z is 16 or 24. A value L derived from the following 32-bit word are used in a manner similar to YZ in lop_fixr: it is xor:ed into the current location minus 4 * L. The first byte of the word is 0 or 1. If it is 1, then L = (lowest 24 bits of word) - 2^Z, if 0, then L = (lowest 24 bits of word).
lop_file
0x9806YYZZ. Y is the file number, Z is count of 32-bit words. Set the file number to Y and the line counter to 0. The next Z * 4 bytes contain the file name, padded with zeros if the count is not a multiple of four. The same Y may occur multiple times, but Z must be 0 for all but the first occurrence.
lop_line
0x9807YYZZ. YZ is the line number. Together with lop_file, it forms the source location for the next 32-bit word. Note that for each non-lopcode 32-bit word, line numbers are assumed incremented by one.
lop_spec
0x9808YYZZ. YZ is the type number. Data until the next lopcode other than lop_quote forms special data of type YZ. See mmo section mapping.

Other types than 80, (or type 80 with a content that does not parse) is stored in sections named .MMIX.spec_data.n where n is the YZ-type. The flags for such a sections say not to allocate or load the data. The vma is 0. Contents of multiple occurrences of special data n is concatenated to the data of the previous lop_spec ns. The location in data or code at which the lop_spec occurred is lost.

lop_pre
0x980901ZZ. The first lopcode in a file. The Z field forms the length of header information in 32-bit words, where the first word tells the time in seconds since 00:00:00 GMT Jan 1 1970.
lop_post
0x980a00ZZ. Z > 32. This lopcode follows after all content-generating lopcodes in a program. The Z field denotes the value of rG at the beginning of the program. The following 256 - Z big-endian 64-bit words are loaded into global registers $G ... $255.
lop_stab
0x980b0000. The next-to-last lopcode in a program. Must follow immediately after the lop_post lopcode and its data. After this lopcode follows all symbols in a compressed format (see Symbol-table).
lop_end
0x980cYYZZ. The last lopcode in a program. It must follow the lop_stab lopcode and its data. The YZ field contains the number of 32-bit words of symbol table information after the preceding lop_stab lopcode.

Note that the lopcode "fixups"; lop_fixr, lop_fixrx and lop_fixo are not generated by BFD, but are handled. They are generated by mmixal.

This trivial one-label, one-instruction file:

      :Main TRAP 1,2,3

can be represented this way in mmo:

      0x98090101 - lop_pre, one 32-bit word with timestamp.
      <timestamp>
      0x98010002 - lop_loc, text segment, using a 64-bit address.
                   Note that mmixal does not emit this for the file above.
      0x00000000 - Address, high 32 bits.
      0x00000000 - Address, low 32 bits.
      0x98060002 - lop_file, 2 32-bit words for file-name.
      0x74657374 - "test"
      0x2e730000 - ".s\0\0"
      0x98070001 - lop_line, line 1.
      0x00010203 - TRAP 1,2,3
      0x980a00ff - lop_post, setting $255 to 0.
      0x00000000
      0x00000000
      0x980b0000 - lop_stab for ":Main" = 0, serial 1.
      0x203a4040   See Symbol-table.
      0x10404020
      0x4d206120
      0x69016e00
      0x81000000
      0x980c0005 - lop_end; symbol table contained five 32-bit words.