You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
269 lines
11 KiB
C++
269 lines
11 KiB
C++
/*
|
|
Servo.cpp - Interrupt driven Servo library for Arduino using 16 bit timers- Version 2
|
|
Copyright (c) 2009 Michael Margolis. All right reserved.
|
|
|
|
This library is free software; you can redistribute it and/or
|
|
modify it under the terms of the GNU Lesser General Public
|
|
License as published by the Free Software Foundation; either
|
|
version 2.1 of the License, or (at your option) any later version.
|
|
|
|
This library is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
|
|
Lesser General Public License for more details.
|
|
|
|
You should have received a copy of the GNU Lesser General Public
|
|
License along with this library; if not, write to the Free Software
|
|
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
|
*/
|
|
|
|
/*
|
|
|
|
A servo is activated by creating an instance of the Servo class passing the desired pin to the attach() method.
|
|
The servos are pulsed in the background using the value most recently written using the write() method
|
|
|
|
Note that analogWrite of PWM on pins associated with the timer are disabled when the first servo is attached.
|
|
Timers are seized as needed in groups of 12 servos - 24 servos use two timers, 48 servos will use four.
|
|
|
|
The methods are:
|
|
|
|
Servo - Class for manipulating servo motors connected to Arduino pins.
|
|
|
|
attach(pin ) - Attaches a servo motor to an i/o pin.
|
|
attach(pin, min, max ) - Attaches to a pin setting min and max values in microseconds
|
|
default min is 544, max is 2400
|
|
|
|
write() - Sets the servo angle in degrees. (invalid angle that is valid as pulse in microseconds is treated as microseconds)
|
|
writeMicroseconds() - Sets the servo pulse width in microseconds
|
|
read() - Gets the last written servo pulse width as an angle between 0 and 180.
|
|
readMicroseconds() - Gets the last written servo pulse width in microseconds. (was read_us() in first release)
|
|
attached() - Returns true if there is a servo attached.
|
|
detach() - Stops an attached servos from pulsing its i/o pin.
|
|
|
|
*/
|
|
|
|
#include <avr/interrupt.h>
|
|
#include <WProgram.h>
|
|
|
|
|
|
#include "Servo.h"
|
|
|
|
#define TICKS_PER_uS (clockCyclesPerMicrosecond() / 8) // number of timer ticks per microsecond with prescale of 8
|
|
|
|
#define SERVOS_PER_TIMER 12 // the maximum number of servos controlled by one timer
|
|
#define TRIM_DURATION (SERVOS_PER_TIMER/2) // compensation ticks to trim adjust for digitalWrite delays
|
|
|
|
#define NBR_TIMERS (MAX_SERVOS / SERVOS_PER_TIMER)
|
|
|
|
static servo_t servos[MAX_SERVOS]; // static array of servo structures
|
|
static volatile int8_t Channel[NBR_TIMERS]; // counter for the servo being pulsed for each timer (or -1 if refresh interval)
|
|
#if defined(__AVR_ATmega1280__)
|
|
typedef enum { _timer5, _timer1, _timer3, _timer4 } servoTimer_t; // this is the sequence for timer utilization on mega
|
|
#else
|
|
typedef enum { _timer1 } servoTimer_t; // this is the sequence for timer utilization on other controllers
|
|
#endif
|
|
|
|
uint8_t ServoCount = 0; // the total number of attached servos
|
|
|
|
// convenience macros
|
|
#define SERVO_INDEX_TO_TIMER(_servo_nbr) ((servoTimer_t)(_servo_nbr / SERVOS_PER_TIMER)) // returns the timer controlling this servo
|
|
#define SERVO_INDEX_TO_CHANNEL(_servo_nbr) (_servo_nbr % SERVOS_PER_TIMER) // returns the index of the servo on this timer
|
|
#define SERVO_INDEX(_timer,_channel) ((_timer*SERVOS_PER_TIMER) + _channel) // macro to access servo index by timer and channel
|
|
#define SERVO(_timer,_channel) (servos[SERVO_INDEX(_timer,_channel)]) // macro to access servo class by timer and channel
|
|
|
|
#define SERVO_MIN() (MIN_PULSE_WIDTH - this->min * 4) // minimum value in uS for this servo
|
|
#define SERVO_MAX() (MAX_PULSE_WIDTH - this->max * 4) // maximum value in uS for this servo
|
|
|
|
/************ static functions common to all instances ***********************/
|
|
|
|
static inline void handle_interrupts(servoTimer_t timer, volatile uint16_t *TCNTn, volatile uint16_t* OCRnA)
|
|
{
|
|
if( Channel[timer] < 0 )
|
|
*TCNTn = 0; // channel set to -1 indicated that refresh interval completed so reset the timer
|
|
else{
|
|
if( SERVO_INDEX(timer,Channel[timer]) < ServoCount && SERVO(timer,Channel[timer]).Pin.isActive == true )
|
|
digitalWrite( SERVO(timer,Channel[timer]).Pin.nbr,LOW); // pulse this channel low if activated
|
|
}
|
|
|
|
Channel[timer]++; // increment to the next channel
|
|
if( SERVO_INDEX(timer,Channel[timer]) < ServoCount && Channel[timer] < SERVOS_PER_TIMER) {
|
|
*OCRnA = *TCNTn + SERVO(timer,Channel[timer]).ticks;
|
|
if(SERVO(timer,Channel[timer]).Pin.isActive == true) // check if activated
|
|
digitalWrite( SERVO(timer,Channel[timer]).Pin.nbr,HIGH); // its an active channel so pulse it high
|
|
}
|
|
else {
|
|
// finished all channels so wait for the refresh period to expire before starting over
|
|
if( (unsigned)*TCNTn < (((unsigned int)REFRESH_INTERVAL * TICKS_PER_uS) + 4) ) // allow a few ticks to ensure the next OCR1A not missed
|
|
*OCRnA = (unsigned int)REFRESH_INTERVAL * TICKS_PER_uS;
|
|
else
|
|
*OCRnA = *TCNTn + 4; // at least REFRESH_INTERVAL has elapsed
|
|
Channel[timer] = -1; // this will get incremented at the end of the refresh period to start again at the first channel
|
|
}
|
|
}
|
|
|
|
SIGNAL (TIMER1_COMPA_vect)
|
|
{
|
|
handle_interrupts(_timer1, &TCNT1, &OCR1A);
|
|
}
|
|
|
|
#if defined(__AVR_ATmega1280__)
|
|
SIGNAL (TIMER3_COMPA_vect)
|
|
{
|
|
handle_interrupts(_timer3, &TCNT3, &OCR3A);
|
|
}
|
|
SIGNAL (TIMER4_COMPA_vect)
|
|
{
|
|
handle_interrupts(_timer4, &TCNT4, &OCR4A);
|
|
}
|
|
SIGNAL (TIMER5_COMPA_vect)
|
|
{
|
|
handle_interrupts(_timer5, &TCNT5, &OCR5A);
|
|
}
|
|
#endif
|
|
|
|
static void initISR(servoTimer_t timer)
|
|
{
|
|
if(timer == _timer1) {
|
|
TCCR1A = 0; // normal counting mode
|
|
TCCR1B = _BV(CS11); // set prescaler of 8
|
|
TCNT1 = 0; // clear the timer count
|
|
#if defined(__AVR_ATmega8__)
|
|
TIFR |= _BV(OCF1A); // clear any pending interrupts;
|
|
TIMSK |= _BV(OCIE1A) ; // enable the output compare interrupt
|
|
#else
|
|
TIFR1 |= _BV(OCF1A); // clear any pending interrupts;
|
|
TIMSK1 |= _BV(OCIE1A) ; // enable the output compare interrupt
|
|
#endif
|
|
}
|
|
#if defined(__AVR_ATmega1280__)
|
|
else if(timer == _timer3) {
|
|
TCCR3A = 0; // normal counting mode
|
|
TCCR3B = _BV(CS31); // set prescaler of 8
|
|
TCNT3 = 0; // clear the timer count
|
|
TIFR3 = _BV(OCF3A); // clear any pending interrupts;
|
|
TIMSK3 = _BV(OCIE3A) ; // enable the output compare interrupt
|
|
}
|
|
else if(timer == _timer4) {
|
|
TCCR4A = 0; // normal counting mode
|
|
TCCR4B = _BV(CS41); // set prescaler of 8
|
|
TCNT4 = 0; // clear the timer count
|
|
TIFR4 = _BV(OCF4A); // clear any pending interrupts;
|
|
TIMSK4 = _BV(OCIE4A) ; // enable the output compare interrupt
|
|
}
|
|
else if(timer == _timer5) {
|
|
TCCR5A = 0; // normal counting mode
|
|
TCCR5B = _BV(CS51); // set prescaler of 8
|
|
TCNT5 = 0; // clear the timer count
|
|
TIFR5 = _BV(OCF5A); // clear any pending interrupts;
|
|
TIMSK5 = _BV(OCIE5A) ; // enable the output compare interrupt
|
|
}
|
|
#endif
|
|
}
|
|
|
|
static boolean isTimerActive(servoTimer_t timer)
|
|
{
|
|
// returns true if any servo is active on this timer
|
|
for(uint8_t channel=0; channel < SERVOS_PER_TIMER; channel++) {
|
|
if(SERVO(timer,channel).Pin.isActive == true)
|
|
return true;
|
|
}
|
|
return false;
|
|
}
|
|
|
|
|
|
/****************** end of static functions ******************************/
|
|
|
|
Servo::Servo()
|
|
{
|
|
if( ServoCount < MAX_SERVOS) {
|
|
this->servoIndex = ServoCount++; // assign a servo index to this instance
|
|
servos[this->servoIndex].ticks = DEFAULT_PULSE_WIDTH * TICKS_PER_uS; // store default values
|
|
}
|
|
else
|
|
this->servoIndex = INVALID_SERVO ; // too many servos
|
|
}
|
|
|
|
uint8_t Servo::attach(int pin)
|
|
{
|
|
return this->attach(pin, MIN_PULSE_WIDTH, MAX_PULSE_WIDTH);
|
|
}
|
|
|
|
uint8_t Servo::attach(int pin, int min, int max)
|
|
{
|
|
if(this->servoIndex < MAX_SERVOS ) {
|
|
pinMode( pin, OUTPUT) ; // set servo pin to output
|
|
servos[this->servoIndex].Pin.nbr = pin;
|
|
// todo min/max check: abs(min - MIN_PULSE_WIDTH) /4 < 128
|
|
this->min = (MIN_PULSE_WIDTH - min)/4; //resolution of min/max is 4 uS
|
|
this->max = (MAX_PULSE_WIDTH - max)/4;
|
|
// initialize the timer if it has not already been initialized
|
|
servoTimer_t timer = SERVO_INDEX_TO_TIMER(servoIndex);
|
|
if(isTimerActive(timer) == false)
|
|
initISR(timer);
|
|
servos[this->servoIndex].Pin.isActive = true; // this must be set after the check for isTimerActive
|
|
}
|
|
return this->servoIndex ;
|
|
}
|
|
|
|
void Servo::detach()
|
|
{
|
|
servos[this->servoIndex].Pin.isActive = false;
|
|
|
|
#ifdef FREE_TIMERS
|
|
if(isTimerActive(SERVO_INDEX_TO_TIMER(servoIndex)) == false) {
|
|
;// call to unimplimented function in wiring.c to re-init timer (set timer back to PWM mode) TODO?
|
|
}
|
|
#endif
|
|
}
|
|
|
|
void Servo::write(int value)
|
|
{
|
|
if(value < MIN_PULSE_WIDTH)
|
|
{ // treat values less than 544 as angles in degrees (valid values in microseconds are handled as microseconds)
|
|
if(value < 0) value = 0;
|
|
if(value > 180) value = 180;
|
|
value = map(value, 0, 180, SERVO_MIN(), SERVO_MAX());
|
|
}
|
|
this->writeMicroseconds(value);
|
|
}
|
|
|
|
void Servo::writeMicroseconds(int value)
|
|
{
|
|
// calculate and store the values for the given channel
|
|
byte channel = this->servoIndex;
|
|
if( (channel >= 0) && (channel < MAX_SERVOS) ) // ensure channel is valid
|
|
{
|
|
if( value < SERVO_MIN() ) // ensure pulse width is valid
|
|
value = SERVO_MIN();
|
|
else if( value > SERVO_MAX() )
|
|
value = SERVO_MAX();
|
|
|
|
value = (value-TRIM_DURATION) * TICKS_PER_uS; // convert to ticks after compensating for interrupt overhead
|
|
uint8_t oldSREG = SREG;
|
|
cli();
|
|
servos[channel].ticks = value;
|
|
SREG = oldSREG;
|
|
}
|
|
}
|
|
|
|
int Servo::read() // return the value as degrees
|
|
{
|
|
return map( this->readMicroseconds()+1, SERVO_MIN(), SERVO_MAX(), 0, 180);
|
|
}
|
|
|
|
int Servo::readMicroseconds()
|
|
{
|
|
unsigned int pulsewidth;
|
|
if( this->servoIndex != INVALID_SERVO )
|
|
pulsewidth = (servos[this->servoIndex].ticks / TICKS_PER_uS) + TRIM_DURATION ;
|
|
else
|
|
pulsewidth = 0;
|
|
|
|
return pulsewidth;
|
|
}
|
|
|
|
bool Servo::attached()
|
|
{
|
|
return servos[this->servoIndex].Pin.isActive ;
|
|
}
|