You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
75 lines
2.3 KiB
Plaintext
75 lines
2.3 KiB
Plaintext
/*
|
|
Debounce
|
|
|
|
Each time the input pin goes from LOW to HIGH (e.g. because of a push-button
|
|
press), the output pin is toggled from LOW to HIGH or HIGH to LOW. There's
|
|
a minimum delay between toggles to debounce the circuit (i.e. to ignore
|
|
noise).
|
|
|
|
The circuit:
|
|
* LED attached from pin 13 to ground
|
|
* pushbutton attached from pin 2 to +5V
|
|
* 10K resistor attached from pin 2 to ground
|
|
|
|
* Note: On most Arduino boards, there is already an LED on the board
|
|
connected to pin 13, so you don't need any extra components for this example.
|
|
|
|
|
|
created 21 November 2006
|
|
by David A. Mellis
|
|
modified 3 Jul 2009
|
|
by Limor Fried
|
|
|
|
|
|
http://www.arduino.cc/en/Tutorial/Debounce
|
|
*/
|
|
|
|
// constants won't change. They're used here to
|
|
// set pin numbers:
|
|
const int buttonPin = 2; // the number of the pushbutton pin
|
|
const int ledPin = 13; // the number of the LED pin
|
|
|
|
// Variables will change:
|
|
int ledState = HIGH; // the current state of the output pin
|
|
int buttonState; // the current reading from the input pin
|
|
int lastButtonState = LOW; // the previous reading from the input pin
|
|
|
|
// the following variables are long's because the time, measured in miliseconds,
|
|
// will quickly become a bigger number than can be stored in an int.
|
|
long lastDebounceTime = 0; // the last time the output pin was toggled
|
|
long debounceDelay = 50; // the debounce time; increase if the output flickers
|
|
|
|
void setup() {
|
|
pinMode(buttonPin, INPUT);
|
|
pinMode(ledPin, OUTPUT);
|
|
}
|
|
|
|
void loop() {
|
|
// read the state of the switch into a local variable:
|
|
int reading = digitalRead(buttonPin);
|
|
|
|
// check to see if you just pressed the button
|
|
// (i.e. the input went from LOW to HIGH), and you've waited
|
|
// long enough since the last press to ignore any noise:
|
|
|
|
// If the switch changed, due to noise or pressing:
|
|
if (reading != lastButtonState) {
|
|
// reset the debouncing timer
|
|
lastDebounceTime = millis();
|
|
}
|
|
|
|
if ((millis() - lastDebounceTime) > debounceDelay) {
|
|
// whatever the reading is at, it's been there for longer
|
|
// than the debounce delay, so take it as the actual current state:
|
|
buttonState = reading;
|
|
}
|
|
|
|
// set the LED using the state of the button:
|
|
digitalWrite(ledPin, buttonState);
|
|
|
|
// save the reading. Next time through the loop,
|
|
// it'll be the lastButtonState:
|
|
lastButtonState = reading;
|
|
}
|
|
|