You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
113 lines
2.8 KiB
Plaintext
113 lines
2.8 KiB
Plaintext
/*
|
|
Row-Column Scanning an 8x8 LED matrix with X-Y input
|
|
|
|
This example controls an 8x8 LED matrix using two analog inputs
|
|
|
|
created 27 May 2009
|
|
modified 29 Jun 2009
|
|
by Tom Igoe
|
|
|
|
This example works for the Lumex LDM-24488NI Matrix. See
|
|
http://sigma.octopart.com/140413/datasheet/Lumex-LDM-24488NI.pdf
|
|
for the pin connections
|
|
|
|
For other LED cathode column matrixes, you should only need to change
|
|
the pin numbers in the row[] and column[] arrays
|
|
|
|
rows are the anodes
|
|
cols are the cathodes
|
|
---------
|
|
|
|
Pin numbers:
|
|
Matrix:
|
|
* Digital pins 2 through 13,
|
|
* analog pins 2 through 5 used as digital 16 through 19
|
|
Potentiometers:
|
|
* center pins are attached to analog pins 0 and 1, respectively
|
|
* side pins attached to +5V and ground, respectively.
|
|
|
|
http://www.arduino.cc/en/Tutorial/RowColumnScanning
|
|
|
|
see also http://www.tigoe.net/pcomp/code/category/arduinowiring/514 for more
|
|
*/
|
|
|
|
|
|
// 2-dimensional array of row pin numbers:
|
|
const int row[8] = {
|
|
2,7,19,5,18,12,16 };
|
|
|
|
// 2-dimensional array of column pin numbers:
|
|
const int col[8] = {
|
|
6,11,10,3,17,4,8,9 };
|
|
|
|
// 2-dimensional array of pixels:
|
|
int pixels[8][8];
|
|
|
|
// cursor position:
|
|
int x = 5;
|
|
int y = 5;
|
|
|
|
void setup() {
|
|
Serial.begin(9600);
|
|
// initialize the I/O pins as outputs:
|
|
|
|
// iterate over the pins:
|
|
for (int thisPin = 0; thisPin < 8; thisPin++) {
|
|
// initialize the output pins:
|
|
pinMode(col[thisPin], OUTPUT);
|
|
pinMode(row[thisPin], OUTPUT);
|
|
// take the col pins (i.e. the cathodes) high to ensure that
|
|
// the LEDS are off:
|
|
digitalWrite(col[thisPin], HIGH);
|
|
}
|
|
|
|
// initialize the pixel matrix:
|
|
for (int x = 0; x < 8; x++) {
|
|
for (int y = 0; y < 8; y++) {
|
|
pixels[x][y] = HIGH;
|
|
}
|
|
}
|
|
}
|
|
|
|
void loop() {
|
|
// read input:
|
|
readSensors();
|
|
|
|
// draw the screen:
|
|
refreshScreen();
|
|
}
|
|
|
|
void readSensors() {
|
|
// turn off the last position:
|
|
pixels[x][y] = HIGH;
|
|
// read the sensors for X and Y values:
|
|
x = 7 - map(analogRead(0), 0, 1023, 0, 7);
|
|
y = map(analogRead(1), 0, 1023, 0, 7);
|
|
// set the new pixel position low so that the LED will turn on
|
|
// in the next screen refresh:
|
|
pixels[x][y] = LOW;
|
|
|
|
}
|
|
|
|
void refreshScreen() {
|
|
// iterate over the rows (anodes):
|
|
for (int thisRow = 0; thisRow < 8; thisRow++) {
|
|
// take the row pin (anode) high:
|
|
digitalWrite(row[thisRow], HIGH);
|
|
// iterate over the cols (cathodes):
|
|
for (int thisCol = 0; thisCol < 8; thisCol++) {
|
|
// get the state of the current pixel;
|
|
int thisPixel = pixels[thisRow][thisCol];
|
|
// when the row is HIGH and the col is LOW,
|
|
// the LED where they meet turns on:
|
|
digitalWrite(col[thisCol], thisPixel);
|
|
// turn the pixel off:
|
|
if (thisPixel == LOW) {
|
|
digitalWrite(col[thisCol], HIGH);
|
|
}
|
|
}
|
|
// take the row pin low to turn off the whole row:
|
|
digitalWrite(row[thisRow], LOW);
|
|
}
|
|
}
|